|
CLUTCH & TRANSMISSION TOOLS |
PRICE |
CLUTCH
INSTALLING TOOLS 1951-1995 AIRHEADS
For assembly/disassembly and aligning of the clutch. Includes
the three bolts needed to remove/install the clutch. Replaces
Matra 529 534 BMW 21 2 650 and 21 2 660 1955-1995 twins.
(Note: For R65 1979-80 order Matra
357a bolts below)
Same Matra
529 clutch aligner as above but with the smaller Matra 357a
bolts to remove/install clutch on R26 R27 R51/3 R67 R67/2 R67/3
and Isetta replaces Matra 357a and 529. |
$36
(0.6 lb.)
$36
(0.6 lb) |
CAMSHAFT/TRANSMISSION BEARING PULLER
To
pull the cam bearing (6203) out of the blind hole in the back of
the pre 1970 engine block, as well as the 3203 and 6203 bearings
supporting the intermediate shaft in the 4 speed tranny. These
bearings will usually fall out if the case is heated, but if you
are having trouble with one of them |
$32
(0.6 lb.)
|
TRANSMISSION
OUTPUT NUT SOCKET 1955-1969 and R24 R25 R26 R27 R51/2 R51/3 R67
R68
For dealing with that funny nut buried in the transmission
output flange. Includes a hold down which keeps the socket from
sliding off the nut. Two sizes: |
|
|
/2 small
nuts 21 mm (.83 in) o.d. used before mid 1967 |
$54
(0.7 lb.) |
|
/2 large
nuts 23 mm (.9 in) o.d.
introduced in mid 1967 |
$54
(0.7 lb.) |
|
Set of two
with one hold down. |
$98
(1.4 lb.) |
|
R12 R24 R25
R26 R27 R51/2 R51/3 R67 R68 same as the small (above) without
hold down. |
$45
(0.6 lb) |
TRANSMISSION
OUTPUT FLANGE HOLDER/PULLER 1951-95 AIRHEADS and R24 R25 R26 R27
R51/2 R51/3 R67 R68
For holding the output flange while unscrewing the output nut.
Also for pulling the flange from its tapered seat. Two different
kinds. |
|
|
Replaces
Matra 500, 501 and BMW 23 1 700/710 FOR 1955-1995 twins |
$78
(1.5 lb.) |
|
Replaces
Matra 422a 494 5070 for R24 R25 R26 R27 R51/2 R51/3 R67 R68 |
$78
(2.5 lb.) |
TRANSMISSION SHIM MEASURING PLATE-5-speed transmissions
1974-on
CNC-machined
aluminum plate bolts onto the transmission and allows for
quick and accurate transmission shim measurement/selection.
Made from 3/8" aluminum tool and jig plate to ensure
flatness to within 0.001".
Replaces BMW tool 23 3 650
|
NEW! $73
|
MOLD-A-GAUGE
Non-stick, non-shrink, heat cured material, used to measure the
end play of the input, intermediate, and output shafts on the /2
/5 /6 /7 R26 R27 and probably other BMW transmissions. Has to be
heated to 275F (135C) for 25 minutes (oven). You will need a
caliper (preferably dial) to measure the thickness of the cured
MOLD-A GAUGE. Replaces
Matra numbers
504 5061 and BMW 23 3 650. Enough for at least 4
transmissions. |
$7
(0.1 lb) |
TRANSMISSION
OUTPUT SHAFT HOLDER /2 /5 R26 R27
Replaces Matra 504, used to support the transmission output
shaft while adjusting the shifter forks. |
$32
(0.4 lb) |
|
Please note: Transmission Shims can be found under
Parts>Clutch &
Transmission. |
|
